Top 10 typical forklift mishaps ， forklift operation ought to take note of these matters ！.

Don't ignore the forklift at the workplace. If the procedure is bad, there will certainly be major accidents in minutes, and there are several crashes involving forklifts.

Case 1: The forklift freight obstructed the driver's sight, and the individual ahead could not be discovered, resulting in a moving mishap.
Situation 2: In order to preserve the equilibrium of the forklift when lifting hefty items, the staff members used their body weight as the counterweight, which nearly created casualties.
Instance 3: The size of the forklift cargo exceeds the allowable width of the path and holds on the roadside shelf, which virtually triggers an accident.
Instance 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not notice the pedestrian, and the pedestrian did not see the forklift.
Case 6: The forklift raises the personnel illegally, the forklift motorist does not put on the seat belt, the forklift lifter falls and the chauffeur is squashed when the forklift rolls over.
Case 7: The forklift chauffeur did not wear a safety belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation need to pay attention to these issues ：.

Begin.
1. Before starting, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and after that begin.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift begins with a load, the driver should first verify that the tons is steady and reputable.
4. The beginning needs to be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too expensive when driving. When entering and leaving the job site or while driving, be careful that there will certainly be no obstacles overhead. When the lots is taking a trip, the fork has to not be elevated expensive, which will certainly influence the stability of the forklift. .
3. After discharging, the fork must be decreased to the regular driving placement prior to driving. .
4. When transforming, if there are pedestrians or automobiles close by, the driving signal should be released first. High-speed doglegs are banned. High-speed doglegs will certainly cause the car to lose side security and tip over. .
5. When the forklift is downhill, it is purely prohibited to turn off the flame and slide, and it is restricted to brake instantly while driving with tons unless there are special situations.
6. When the forklift is running, it should obey the traffic rules in the manufacturing facility and have to maintain a certain security range from the vehicle in front. .
7. When the forklift is running, the lots needs to remain in the lowest placement that does not hinder the driving, and the gantry ought to be properly tilted back. The tons will not be raised except when piling or loading. .
8. The height of the lots should not obstruct the driver's sight. In unique circumstances, when the item impacts the forward vision, drive at a reduced speed when reversing.
9. It is prohibited to switch on the ramp, nor to drive throughout the ramp. .
10. The risk-free driving rate of the forklift in the manufacturing facility location is 5 km/h, and it must drive safely at a reduced rate when getting in the manufacturing workshop area. .
11. When the forklift is raised, lifted or driven, it is restricted for personnel to base on the fork to hold products and play a balancing role. .
12. If issues are found, they will be fixed and reported in a prompt manner, and they will certainly never run with ailments or hide them.

filling and unloading.
1. When fork-loading products, the distance between both forks ought to be readjusted as needed to make the load of the two forks well balanced and not skewed, and one side of the thing need to protest the rack. .
2. It is restricted to collaborate with a solitary fork or make use of a fork top or draw. In special situations, safety indication should Stand-on Electric Pallet Stacker be set up to Stand-on Electric Pallet Stacker advise surrounding pedestrians. .
3. In the process of packing and dumping items, the forklift needs to be stopped with the brake. .
4. The rate of the lorry ought to be sluggish and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and hurt individuals. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the lots, and it ought to be kept in mind that the fork suggestion need to not touch other products or things. The load must be stabilized with very little back tilt of the gantry to ensure that the lots does not slide backwards. The mast can be tilted ahead somewhat when the lots is lowered to allow for simple positioning of the tons and removal of the forks. .
6. It is prohibited to fork products at broadband and ram tough things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to loaf the fork, so regarding stay clear of the collapse of the goods and injure individuals. .
8. Overwhelming is forbidden, and it is forbidden to make use of forks to lift workers to participate in high-altitude operations to avoid high-altitude dropping accidents. .
9. It is not allowed to make use of the brake inertia to slip, put, round or roll things. .
10. It is not enabled to use forks to choose, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the things on the fork are in the air. Prior to leaving the forklift, you need to discharge the goods or reduced the fork frame.
2. Pull the hand brake deal with to dead or depress the hand brake switch.
3. The engine is turned off and the power is removed. (Except for special circumstances, such as the vehicle driver does not leave the car's view and does not go beyond 1 minute).
4. Get rid of the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance must be checked, and fuel, lubing oil and air conditioning water ought to be included.
2. Examine the safety performance of beginning, running and stopping.
3. Examine whether the lights and horn signals are complete and efficient.
4. During the procedure of the forklift, check whether the pressure and temperature are regular.
5. After the forklift is running, the external leak should also be checked and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine before leaving the cars and truck;.
2. When you run into a person in front of you throughout driving, you need to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The turning should not be also sharp to avoid the tendency of " complimentary turning";.
6. Running up and down the incline must be sluggish and uniform, and no turning on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is above 10%, the car should be driven in reverse when declining;.
8. When the forklift workers lug the goods and progress, if they experience huge or heavy goods and most likely to the vehicle driver's line of vision, they should take the turning around exercise
.
The "Eight Prohibitions" must be followed in the procedure.
1. Single fork procedure is not permitted.
2. It is not enabled to raise the goods for cross country driving.
3. It is not allowed to pick up the goods by handing over the pallet with the fork.
4. It is not enabled to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to use inertia force to pick up the goods.
6. It is not permitted to use braking force to expatriation round or easy-to-roll things.
7. It is not permitted to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is elevated.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the following conditions.
1. Contours, narrow roadways, train crossings;.
2. Areas with a longitudinal slope greater than 5%.
3. When there is an obstacle on one side of the roadway, the contrary side of the area with the very same length as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844